WELCOME TO Hongkong NKF Machinery Co.,Limited. English | Spanish

motorcycle bearings

motorcycle bearings
Author :Admin | Publish Date:2013-01-14 10:29:15
motorcycle bearings, as most, require a slight preload so that more than one ball under the cone (inner race) will support its load. With proper preload, slight drag should be perceptible. Preload drag is small compared to drag caused by wheel loads, neither of which are significant regardless of adjustment. In contrast bearing life is affected by proper adjustment. Adjusting ball bearings to spin freely unloaded does not reduce operating friction because a bearing with proper preload has lower drag when loaded than one with clearance. For high quality bearings, preload should be just enough to cause light drag when rotating the axle between thumb and forefinger. Low grade bearings will feel slightly lumpy with proper preload.


Motorcycle bearings support the wheel hubs on the axles. Bearings require a certain amount of pressure, otherwise referred to as preload. The specific amount of preload determines the number of bearings that support the wheel hubs at any given time. Cone flats thread onto the axles and press bearing cones against the bearings. Adjusting bearing cone preload prolongs the life of the bearings. With proper preload, light drag should be noticed when spinning the wheels.
Wheels with quick-release levers present a challenge. Closing the lever alters the preload. Adjusting nsk bearings on wheels that have quick-release levers may take several attempts.


The motorcycle bearings sit between a cone screwed to the wheel axle and the cup in the wheel hub. They must be properly adjusted and greased. To find out if they need greasing without taking everything apart, simply remove the wheel from the bike, support the axle horizontally with your fingers, and turn the wheel slowly--try not to tilt the axle as it rotates. If the wheel does not turn smoothly or you can feel tiny bumps in your fingers, then you must dismantle the bearing assembly and service the bearings.


Motorcycle bearings should last for years and provide you with thousands of miles of travel---but they won't last forever. In some cases they even fail completely if they haven't been maintained correctly. Part of a maintenance schedule should include replacement of wheel bearings before they fail. The procedure isn't that difficult if you have about an hour and a few small tools. Front and back wheels are similar in procedure to change ntn bearings and only require slightly different tooling.


Motorcycle bearings cost are typically located right at the spindle of the wheel hub to allow free wheel movement. By minimizing the friction that goes with metal to metal surface contacts as your car rotates, the functionality of the part is crucial to the overall performance of your vehicle. Keeping the part periodically greased or re-packed every two years, which is equivalent to 24,000-mile service, is essential to keep it in top notch working conditions. Proper greasing could also facilitate efficient flushing mechanisms to do away with any form of contaminants which can induce wearing and corrosion. Once the part fails, find immediate replacement for your wheel will not run properly without working sets of motorcycle bearings. 


To establish strength and rigidity, the part is crafted from high grade and durable metal alloy constructions to have better resistance to heat, pressure, and wearing. Available for specific vehicle applications, there is no point delaying the replacements of damaged and worn bearings. Continuously agonizing on the grinding noises and erratic driving control that comes with battered bearings is wrong economy for you are fooling around with diving safety. More serious damages may be incurred where you can be facing more tremendous amount of repair costs. Investing with premium and high grade car wheel bearing replacements could instantly restore or 0 re-establish the handling features of your vehicle. 


The "motorcycle bearings"  sit between a cone screwed to the wheel axle and the cup in the wheel hub. They must be properly adjusted and greased. To find out if they need greasing without taking everything apart, simply remove the wheel from the bike, support the axle horizontally with your fingers, and turn the wheel slowly--try not to tilt the axle as it rotates. If the wheel does not turn smoothly or you can feel tiny bumps in your fingers, then you must dismantle the bearing assembly and service the bearings.


pinion stuffing  152x127x12 (415725)
stuffing crown   222,25x184,5x14,28
cup 93125

Contact Us

TEL:00852-54978621
FAX:00852-54979628
Email:sales@dbearings.com
Add:UNIT 04,7/F BRIGHT WAY TOWER,NO 33 MONG KOK ROAD,KL
WhatsApp:8618112377009

timken information lists

Copyright © 2014 Hongkong NKF Machinery Co.,Limited. All rights reserved. TEL:00852-54978621 FAX:00852-54979628 Email:sales@dbearings.com